10DOF I2C/SPI MPU9250 BMP280 GY-91 BME280 Kompass Barom For Arduino Raspberry Pi

• Popularity - 25728 views, 3675.4 views per day, 7 days on eBay. Super high amount of views. 699 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

Home<br>Arduino<br>Module<br>Sensor<br>Chips<br>About Us<br>10DOF I2C/SPI MPU9250 BMP280 GY-91 BME280 Kompass Barom for Arduino Raspberry Pi<br>BMP280<br>Druckbereich: 300-1100 hPa (9000 Meter über dem Meeresspiegel auf -500m)<br>Relative Genauigkeit (bei 950 - 1050 hPa bei 25°C): ±0.12 hPa, equiv. zu ±1 m<br>Absolute Genauigkeit (bei (950 - 1050 hPa, 0 - +40 °C): ±0.12 hPa, equiv. zu ±1 m<br>Netzspannung: 1,8 V - 3,6 V<br>Stromverbrauch: 2,7µA bei 1Hz Ausleserate<br>Temperaturbereich: -40 bis +85°C<br>Package included:<br>1x BMP280 Sensor Bord inklusive Stiftleiste<br>BMP280 MPU9250<br>Chip: MPU-9250 + BMP280<br>Power supply: 3-5v (internal low dropout regulator)<br>Communication: standard IIC / SPI communications protocol<br>Chip built 16bit AD converter, 16-bit data output<br>Gyroscopes range: ± 250 500 1000 2000 ° / s<br>Acceleration range: ± 2 ± 4 ± 8 ± 16g<br>Magnetic field range: ± 4800uT<br>Pressure range: 300-1100hPa<br>Using Immersion Gold PCB, machine welding process to ensure quality<br>2.54mm pin pitch<br>Module size:(L*W)2.05* 1.43cm/0.81"*0.56"<br>Package Included:1x   MPU9250 BMP280 10DOF Acceleration Gyroscope Compass Nine Shaft GY-91 Sensor<br>GY-BME280-3.3V<br>ME-BME280 is a Breakout Board featuring a Sensortec ME280 Temperature, Humidity & Pressure Sensor.<br>The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.<br>Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k, protocol selector resistor 0ohm (R1), decoupling capacitors 0.1uF on both power supply pins Vdd & Vdd_IO.<br>If you connect board to both power rails VDD_IO 1.8V and VDD 3.3V be sure to remove the power rail jumper GS1!<br>BME280 Features<br>Package 2.5 mm x 2.5 mm x 0.93 mm metal lid LGA<br>Digital interface I2C (up to 3.4 MHz) and SPI (3 and 4 wire, up to 10 MHz)<br>Supply voltage VDD main supply voltage range: 1.71 V to 3.6 V<br>VDDIO interface voltage range: 1.2 V to 3.6 V<br>Current consumption 1.8 uA @ 1 Hz humidity and temperature<br>2.8 uA @ 1 Hz pressure and temperature<br>3.6 uA @ 1 Hz humidity, pressure and temperature<br>0.1 uA in sleep mode<br>Operating range -40…+85 C, 0…100 % rel. humidity, 300…1100 hPa- Humidity sensor and pressure sensor can be independently enabled/disabled<br>Package Included:<br>1PCS I2C/SPI Breakout Temperature Humidity Barometric Pressure BME280 Digital Sensor<br>GY-BME280-5V<br>BME280, the precision sensor from It, is soldered onto PCB.<br>Not only the pressure and the temperature, this sensor can measure humidity.<br>It uses both I2C and SPI (supports 3-, 4-wire SPI) interface<br>Specifications:<br>Supply Voltage: 1.8 - 5V DC<br>Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)<br>Operational Range:<br>Temperature: -40 to +85°C<br>Humidity: 0-100%<br>Pressure: 300-1100 hPa<br>Resolution:<br>Temperature: 0.01°C<br>Humidity: 0.008%<br>Pressure: 0.18Pa<br>Accuracy:<br>Temperature: +-1°C<br>Humidity: +-3%<br>Pressure: +-1Pa<br>I2C address<br>SDO LOW ： 0x76<br>SDO HIGH：　0x77<br>Package Included:<br>1 x Breakout Temperature Humidity Barometric Pressure BME280 Digital Sensor Modul<br>Payment<br>Shipping<br>Refund<br>Payment<br>We accept PayPal only.<br>But we only<br>Accept<br>your<br>Ebay Address<br>,Please Make sure it's 100% right.<br>Payment must be received in 5 business days of auction closing.<br>Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.<br>Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.<br>Shipping<br>Fill your shipping info<br>Refund<br>All package need to<br>